Adhere to these cleaning, maintenance and simple repair procedures on a periodic basis to ensure proper operation of your PEMF Device.

If your PEMF Device requires factory service, in or out of warranty, click here for instructions and procedures.

GENERAL MAINTENANCE AND CONNECTOR ISSUES

+ Basic Maintenance

  • Use a small air compressor and vacuum at the same time. If you have a Magnus Pro X1 or X2 model (box), gently tip it sideways and blow the air in any crack/vent on the faceplate, even around the perimeter. You will see clouds of "stuff" coming out that may have been concentrated to one area.
  • Keep the air flowing in that same entrance location, and put your vacuum where it is coming out. If you have a spark gap chamber device, you will get most of the debris coming out the bottom corners of the faceplates.
  • Keep your loops clean! We recommend [Goo Gone Clean Up Wipes][1], available through Amazon.

+ Damaged Neutrik Connectors

  • Generally, damage is a result of excessive stress on the delivery loop lead. Should the connector become damaged, with the wire lead being pulled out, a self repair process not possible. These connectors are fabricated by our vendors. If these are damaged, the entire cable must be sent to the factory for repair.

+ Damaged Eclipse Connectors

  • A Magnus Pro may be fabricated with with Eclipse Connectors. These connectors are molded into the cable, by the cable vendor, PRIOR to our factory receiving them. If these are damaged, the entire cable *must be sent to the factory for repair, and in some casea they must be replaced.

Magnus Pro X1 HP

+ X1 HP Factory Reset/Recalibration Instructions - do this once a month!

  • Sequence of factory procedures for high-powered, solid-state devices (Magnus Pro X1 HP, formerly the Magnus Compact Portable SS)
    • Resetting Factory Settings
      • Plug the coil and the power cord into the unit.
      • Rotate the power knob to the number 10 position.
      • Press and hold the 5-minute start button.
      • Turn on the power with the rocker switch. The unit will beep 6 times, and both buttons will continue to rapidly flash.
      • Turn unit off to store settings.
    • Voltage Calibration Procedures
      • Plug the coil and the power cord into the unit.
      • Rotate the power knob to the number 2 position.
      • Press and hold the 5-minute start button.
      • Turn on the power with the rocker switch. The unit will pulse 6 times until both button lights flash continuously.
      • Your device will now be calibrated to the current line voltage. Turn the unit off to store settings.
      • Your unit is now ready for use at the current line voltage.

+ X1 HP Factory Reset/Turn Beeping off

  • Sequence of factory procedures for high-powered, solid-state Devices (Magnus Pro X1 HP)
    • Resetting Factory Settings
      • Plug the power cord into the unit.
      • Select #1 on the intensity dial.
      • Press and hold the 5-minute start button.
      • Turn on the power with the rocker switch. The device will pulse and lights will flash continuously.
      • Turn the unit off to store settings.

Magnus Pro X2 MP

+ X2 MP Factory Reset/Turn Beeping off

  • Sequence of factory procedures for mid-powered, solid-state devices (Magnus Pro X2 MP)
    • Resetting Factory Settings (See the below video for demonstration)
      • Plug the power cord into the unit.
      • Press and hold the left side increase/decrease arrow buttons.
      • Turn on the power with the rocker switch. The unit will beep 6 times, and two lights will rapidly flash.
      • Turn the unit off to store settings.
    • Turn Off Beeping at the End of a Session (See the below video for demonstration)
      • Plug the power cord into the unit.
      • Press and hold the left side 5-minute start button and arrow up button.
      • Turn on the power with the rocker switch. The unit will pulse 1 time, and one light will flash continuously.
      • Turn the unit off to store settings.

+ Magnus Pro X2 MP that will not power up

  • If your Magnus Pro X2 does not power up, it may be due to something as simple as a blown fuse.
  • Watch this short video on how to inspect the fuse.
  • You can order extra fuses at Digikey.com.

Magnus Pro X1 MP

+ X1 MP Factory Reset

  • Resetting Factory Settings
    • Unplug the coil from the unit.
    • Watch the below video for a demonstration.

+ Sequence of Factory Procedures for Low-Powered, Solid-State Devices (Magnus Pro X1 MP, formerly the Magnus Compact Clinic SS)

  • Resetting Factory Settings
    • Plug the coil and the power cord into the unit.
    • Hold the left and center button in while turning the device's power button "on."
    • You will hear 6 beeps, and all three buttons will flash.
    • The device will need to be turned "off" and back "on" again to be functional.
  • Turn Tone On/Off
    • The beep sound can be turned on or off.
    • Plug the coil and power cord into the unit.
    • Turn the power knob to the number 1 position.
    • Press and hold the 5-minute button.
    • Turn the rocker switch on.
    • The 5-minute button will rapidly flash.
    • Turn the unit off to store settings.